How to Install Circular Saw Blade

Last Updated on October 31, 2021

Circular saws are extremely handy nowadays to cut objects in a circular motion, and it serves as an alternative to the handling of all the complex machinery out there. Whether it’s the wood or plastic that needs a better form, or metal that requires a better shape, a circular saw has got you all covered up.

These tools are unconditionally benefitting, but they require the installation of new blades from time to time. But once you have acquired the skill, it serves as a great tool to save both your time and energy.

With this perception, let’s get moving to the rudimentary steps- how you would be able to install a circular saw blade.

Steps To Installing A Circular Blade

A saw blade works fine if the depth of the blade is precise owing to the work required and the teeth are set at proper positions. Handheld saws or saws mounted to a machine have different requirements for blades and need to be adjusted based on the depth to which the objects are required to be cut.

Learn a few points regarding the use of this power saw;

Safety First

The first and foremost point regarding the usage must be safety first because we don’t want to get hurt while working. So, do not forget to wear gloves, read all the proper instructions included with the specific model you’re using, wear safety goggles and you’re good to go.

Choose Your Saw Wisely

There are plenty of saws to choose from. You can get one from a high-end brand or a local one depending on your budget, but as long as it works fine, there ought to be no trouble if the basic infrastructure remains the same. A hand-held one is more conventional than the others like miter saw and chop saws.

Aim For The Right Blade

If your purpose is only limited to domestic necessities, blades ranging from 10-15 cm are the ones you should go for as the sizes of the blades matter a lot while handling. But in case you think you might need this device for heavy handling, blades ranging from 20-40 cm would be the best choice.

Handle The Saw

Remember to use the saw by holding both the front and rear handles carefully and adequately. Both handles should be held for proper positioning, and to move the saw you need to use the rear handle trigger.

Measure Your Piece

Make bold lines on the surface of the object you’re going to use the saw on, using a ruler. The lines should be precisely measured, and the saw should be run once over the lines, to avoid faulty lines.

Installing The Blade

The blade should be installed at a distance of around 0.5 cm under the lower part of the object. Teeth of the saw should be kept at a farther distance because it might cause injury. The depth should not exceed 0.7 cm to prevent keeping irregular and faulty lines behind. Also, you will have to check the arbor regularly.

How To Remove The Blade of A Circular Saw?

The first step is to unplug the saw before removing the blade. You should always remember to check the arbor properly. The nut, visible on the arbor of the blade should be unscrewed using a wench and the blades will eventually come sliding off. After the removal is done, the nut should be screwed back again tightly.

Uses of A Circular Saw

  • Cutting plywood
  • Masonry
  • Plastic industry
  • Framing materials
  • Metalwork
  • Cutting holes for pipes

Tips For The Long Run!

Here are some quick tips for you;

  • Do not adjust the blade too deep.
  • Grip both the handles with maximum efficiency.
  • Make double lines with a ruler to cut according to your desired space.
  • Do not put extreme pressure on the blade.
  • Do not press the trigger unless you’re preparing to cut.
  • Do not rest the object on top of a weak table to prevent it from getting cut as well.
  • Screw the nut tightly after you have done changing the blade.
  • Take precautions before starting the saw.

Final Thoughts

Wrapping it up, it can be said that a circular saw is a savior in most household and domestic chores and it is as easy to use if maintained and handled with proper precautions and techniques.

When buying one, you should consider the diameter of the blades as per your field of use and the manual handling of the saw.

A clever technique would be to purchase one with levers that allow for quick adjustment of depth and angle without working hard on the adjustments yourself.